ring motor
英 [rɪŋ ˈməʊtə(r)]
美 [rɪŋ ˈmoʊtər]
网络 环状电机
双语例句
- Slip ring motor starter panel The rear of the frame was carried on a pair of smooth irons forming a sledge.
滑环式电动机起动器掣板机身的尾部安装在一对平滑的铁板上。 - Removing all parts of cover, rings, carbon brush, brush box, brush box shell and short circuit ring equipment ( some motor have no short circuit ring equipment).
先拆下电动机的护罩、滑环、碳刷、刷盒、刷盒支架及短路环装置（有的电机无短路环装置）等全部零件。 - Komatsu rotary reducer, slewing ring, rotary motor, engine four supporting etc pure accessories.
小松回转减速箱、回转支承、回转马达、发动机四配套等纯正配件。 - Electric platform carrier slip ring motor starter panel
电动固定平板搬运车 - Remove brushes and short the ring together with a copper link in case of a slip ring motor ( wound rotor).
如果是（绕线转子）滑环电机，则，移开电刷，同时，用铜链节将滑环短路。 - The machine unit is made up of charging bucket, stepped gear, pulverizing knife, gear ring, pulverizing motor, discharging port, fan blade, aggregating box, dust collection box, etc.
该机由加料斗、分级轮、粉碎刀片、齿圈、粉碎电机、出料口、风叶、集料箱、吸尘箱等部分组成。 - Multi-objective Mixed H_2/ H_ ∞ Control for Ring Torque Motor based on Parameter Optimization Method
基于Q参数优化的环形力矩电机多目标混合H2/H∞控制 - The functional design and hardware component of control system were introduced, and the control calculation of driving ring plate with step motor was deduced in details.
介绍了控制系统的功能设计及硬件组成，重点推导了用步进电机驱动钢领板的控制算法。 - In order to enhance motor torque density to meet the requirements of NC machine tools limited operating space, a novel dual-rotor permanent magnet ring torque motor for NC rotary table is researched.
为提高电机转矩密度，研究了一种直接驱动式新型数控转台双转子永磁环形力矩电机，以适应数控机床作业空间有限的要求。 - Ring permanent magnet torque motor servo system, used in direct drive NC rotary table, suffers from the effect of load torque change, which greatly reduces the servo dynamic stiffness.
数控转台用环形永磁力矩电动机回转送进系统采用直接驱动技术后，对负载转矩变化更为敏感，严重影响系统的动态伺服刚度，使系统的伺服性能大大降低。 - The traveling-wave and traveling-wave-oid are observed experimentally in the ring stators of ultrasonic motor by single-phase drive.
超声电机环形定子上的驻波变形和振型旋转的现象在实验中被观察到，行波和类行波出现在单相激励情况下。 - Design of Dual-Rotor Permanent Magnet Ring Torque Motor for NC Rotary Table
数控转台双转子永磁环形力矩电机设计 - Multi-objective mixed l_1/ H_ ∞ controller for direct drive ring permanent magnet torque motor
直接驱动环形永磁力矩电机多目标混合l1/H∞控制 - Electric Control System of Dance Wire Drawing Machine Drived by Slip ring Motor
用滑差电机驱动的活套式拉丝机电控系统 - Study on Soldering Process for Rotor End Ring of Special Canned Motor
特种屏蔽电机转子端环钎焊工艺的研究 - Effect of curvature change in stator ring of radial piston motor on its pressure angle and torque
内曲线液压马达定子环形状改变对其压力角和扭矩的影响 - Some Analysis of Ring Type Ultrasonic Motor in the Manufacturing Process
环形超声波电动机制作过程中的几点分析 - Study on Design and Process of Rotor Strengthen Ring in Magnetic Levitation Motor
磁悬浮电机转子加强环设计及工艺研究 - Study on Fuzzy-Sliding Model Control NC Rotary Table Permanent Magnet Ring Torque Motor Servo System
数控转台环形力矩电机伺服系统模糊滑模控制的研究 - This paper describes the reason for burnt sliding ring of coiling motor used for clamshell crane, puts forward preventative measures and suggestions and introduces repairing standard and method.
本文叙述了精矿库抓斗吊车绕线式电机滑环烧损原因，提出了预防措施和建议，介绍了滑环修复标准和方法。 - Analysis on the degree of safety and durability for the structure of high-speed accommodation ring road for motor test
汽车试验专用高速环形道路结构安全度和耐久性影响因素分析 - We lay undue emphasis on a new type standing wave ring ultrasonic motor which are presented in the dissertation, which characteristic is that three transducer work at the same time and stator is taper.
本文设计的重点是设计一种新型的环形驻波超声波电机，此电机的特点是三个换能器同时激励、定子圆环带有锥度。 - The technological method of the medium ˉ frequency induction braze welding with heating of the rotor copper bar and end ring for the motor is described in this paper.
本文介绍了发电机转子铜条与端环中频感应加热钎焊的工艺方法。 - Repair Method and Process of Slide Ring for Synchronous Motor
同步电机滑环的修复方法和工艺 - The Vibration Analyses of the Vibrator of a Ring type Ultrasonic Motor with Projection
圆环凸起型压电振子的振动分析 - Natural Frequency of the stator of Ring Ultrasonic Motor Analysis of an RC Loop Multivibrator Output Waveform
环形超声波电动机定子振动的固有频率RC环形多谐振荡器输出波形分析 - Stator Vibration Mode Analysis of Ring-type Ultrasonic Motor
环形超声波电机定子振动模式分析 - The RM166/ 100 ring torque motor from Germany Cytec Company is adopted as the controlled object in this study. Based on its mathematical model, two proposed control strategies are investigated by simulation using MATLAB software.
本文以德国CyTec公司生产的RM166/100型环形力矩电机为控制对象，建立系统数学模型，并利用MATLAB软件对上述两种控制策略进行仿真研究及分析。 - The compound A/ C axis that combined ring permanent magnet torque motor with the direct drive technology can complete precise, high speed and a reliable processing.
环形永磁力矩电机与直接驱动技术相结合形成的复合A/C轴，能完成更加精密、高速和可靠的加工。